User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            Tektronix 2232 Sub7
DATE:                  12-Aug-93
AUTHOR:                User Contributed
REVISION:
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       49
NUMBER OF LINES:       347
CONFIGURATION:         Fluke 6060B
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-   R     N              P                            F        W
  1.002  ASK+                                          X
#----------------------------- 60MHz -----------------------------------------
  1.003  HEAD         {}
  1.004  HEAD         {Can a stable 60MHz 1 division display be obtained}
  1.005  HEAD         {adjusting the A TRIGGER LEVEL control?}
  1.006  HEAD         {}
  1.007  HEAD         {CH1, A trigger mode P-P AUTO, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
  1.008  JMP          2.001
  1.009  EVAL   Dummy
  2.001  HEAD         Internal A and B Triggering Test
  2.002  DISP         Move the Fluke 6061A RF OUTPUT via a 50ê feedthru
  2.002  DISP         termination to the UUT CH1 input connector.
  2.003  DISP         Set the UUT VERTICAL controls as follows:
  2.003  DISP
  2.003  DISP         ÿ   MODE ........................................... CH1
  2.004  DISP         Set the UUT HORIZONTAL controls as follows:
  2.004  DISP
  2.004  DISP         ÿ   MODE ............................................. A
  2.004  DISP         ÿ   A & B SEC/DIV ................. (A & B LOCKED) 0.1æs
  2.004  DISP         ÿ   X10 Magnifier ........................ On (knob out)
  2.005  DISP         Set the UUT B TRIGGER controls as follows:
  2.005  DISP
  2.005  DISP         ÿ   SLOPE ............................... + (button out)
  2.006  6060         60MH                         50mVpp         -D    S
  2.007  MESS         Can a stable display be obtained by adjusting the
  2.008  EVAL   A TRIGGER LEVEL control?
  3.001  HEAD         {}
  3.002  HEAD         {CH1, A trigger mode P-P AUTO, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
  3.003  JMP          4.001
  3.004  EVAL   Dummy
  4.001  HEAD         Internal A and B Triggering Test
  4.002  6060         60MH                         50mVpp         -D    S
  4.003  DISP         Set the UUT A TRIGGER controls as follows:
  4.003  DISP
  4.003  DISP         ÿ   SLOPE ................................ - (button in)
  4.004  EVAL   A TRIGGER LEVEL control?
  5.001  HEAD         {}
  5.002  HEAD         {CH1, A trigger mode NORM, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
  5.003  JMP          6.001
  5.004  EVAL   Dummy
  6.001  HEAD         Internal A and B Triggering Test
  6.002  6060         60MH                         50mVpp         -D    S
  6.003  DISP         Set the UUT A TRIGGER controls as follows:
  6.003  DISP
  6.003  DISP         ÿ   A TRIGGER MODE ................................ NORM
  6.004  EVAL   A TRIGGER LEVEL control?
  7.001  HEAD         {}
  7.002  HEAD         {CH1, A trigger mode NORM, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
  7.003  JMP          8.001
  7.004  EVAL   Dummy
  8.001  HEAD         Internal A and B Triggering Test
  8.002  6060         60MH                         50mVpp         -D    S
  8.003  DISP         Set the UUT A TRIGGER controls as follows:
  8.003  DISP
  8.003  DISP         ÿ   SLOPE ............................... + (button out)
  8.004  EVAL   A TRIGGER LEVEL control?
  9.001  HEAD         {}
  9.002  HEAD         {CH1, B trigger mode NORM, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
  9.003  JMP          10.001
  9.004  EVAL   Dummy
 10.001  HEAD         Internal A and B Triggering Test
 10.002  6060         60MH                         50mVpp         -D    S
 10.003  DISP         Set the UUT HORIZONTAL controls as follows:
 10.003  DISP
 10.003  DISP         ÿ   MODE ............................................. B
 10.004  DISP         Set the UUT A TRIGGER controls as follows:
 10.004  DISP
 10.004  DISP         ÿ   A TRIGGER MODE ............................ P-P AUTO
 10.005  DISP         Set the UUT B TRIGGER controls as follows:
 10.005  DISP
 10.005  DISP         ÿ   LEVEL ..................................... Midrange
 10.006  EVAL   B TRIGGER LEVEL control?
 11.001  HEAD         {}
 11.002  HEAD         {CH1, B trigger mode NORM, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 11.003  JMP          12.001
 11.004  EVAL   Dummy
 12.001  HEAD         Internal A and B Triggering Test
 12.002  6060         60MH                         50mVpp         -D    S
 12.003  DISP         Set the UUT B TRIGGER controls as follows:
 12.003  DISP
 12.003  DISP         ÿ   SLOPE ................................ - (button in)
 12.004  EVAL   B TRIGGER LEVEL control?
 13.001  HEAD         {}
 13.002  HEAD         {CH2, A trigger mode P-P AUTO, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 13.003  JMP          14.001
 13.004  EVAL   Dummy
 14.001  HEAD         Internal A and B Triggering Test
 14.002  DISP         Move the Fluke 6061A RF OUTPUT via a 50ê feedthru
 14.002  DISP         termination to the UUT CH2 input connector.
 14.003  DISP         Set the UUT VERTICAL controls as follows:
 14.003  DISP
 14.003  DISP         ÿ   MODE ........................................... CH2
 14.004  DISP         Set the UUT HORIZONTAL controls as follows:
 14.004  DISP
 14.004  DISP         ÿ   MODE ............................................. A
 14.005  DISP         Set the UUT B TRIGGER controls as follows:
 14.005  DISP
 14.005  DISP         ÿ   SLOPE ............................... + (button out)
 14.006  6060         60MH                         50mVpp         -D    S
 14.007  MESS         Can a stable display be obtained by adjusting the
 14.008  EVAL   A TRIGGER LEVEL control?
 15.001  HEAD         {}
 15.002  HEAD         {CH2, A trigger mode P-P AUTO, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 15.003  JMP          16.001
 15.004  EVAL   Dummy
 16.001  HEAD         Internal A and B Triggering Test
 16.002  6060         60MH                         50mVpp         -D    S
 16.003  DISP         Set the UUT A TRIGGER controls as follows:
 16.003  DISP
 16.003  DISP         ÿ   SLOPE ................................ - (button in)
 16.004  EVAL   A TRIGGER LEVEL control?
 17.001  HEAD         {}
 17.002  HEAD         {CH2, A trigger mode NORM, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 17.003  JMP          18.001
 17.004  EVAL   Dummy
 18.001  HEAD         Internal A and B Triggering Test
 18.002  6060         60MH                         50mVpp         -D    S
 18.003  DISP         Set the UUT A TRIGGER controls as follows:
 18.003  DISP
 18.003  DISP         ÿ   A TRIGGER MODE ................................ NORM
 18.004  EVAL   A TRIGGER LEVEL control?
 19.001  HEAD         {}
 19.002  HEAD         {CH2, A trigger mode NORM, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 19.003  JMP          20.001
 19.004  EVAL   Dummy
 20.001  HEAD         Internal A and B Triggering Test
 20.002  6060         60MH                         50mVpp         -D    S
 20.003  DISP         Set the UUT A TRIGGER controls as follows:
 20.003  DISP
 20.003  DISP         ÿ   SLOPE ............................... + (button out)
 20.004  EVAL   A TRIGGER LEVEL control?
 21.001  HEAD         {}
 21.002  HEAD         {CH2, B trigger mode NORM, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 21.003  JMP          22.001
 21.004  EVAL   Dummy
 22.001  HEAD         Internal A and B Triggering Test
 22.002  6060         60MH                         50mVpp         -D    S
 22.003  DISP         Set the UUT HORIZONTAL controls as follows:
 22.003  DISP
 22.003  DISP         ÿ   MODE ............................................. B
 22.004  DISP         Set the UUT A TRIGGER controls as follows:
 22.004  DISP
 22.004  DISP         ÿ   A TRIGGER MODE ............................ P-P AUTO
 22.005  EVAL   B TRIGGER LEVEL control?
 23.001  HEAD         {}
 23.002  HEAD         {CH2, B trigger mode NORM, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 23.003  JMP          24.001
 23.004  EVAL   Dummy
 24.001  HEAD         Internal A and B Triggering Test
 24.002  6060         60MH                         50mVpp         -D    S
 24.003  DISP         Set the UUT B TRIGGER controls as follows:
 24.003  DISP
 24.003  DISP         ÿ   SLOPE ................................ - (button in)
 24.004  EVAL   B TRIGGER LEVEL control?
#------------------------------- 100MHz --------------------------------------
 25.001  HEAD         {}
 25.002  HEAD         {Can a stable 100MHz 1.5 division display be obtained}
 25.003  HEAD         {adjusting the TRIGGER LEVEL control?}
 25.004  HEAD         {}
 25.005  HEAD         {CH1, A trigger mode P-P AUTO, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 25.006  JMP          26.001
 25.007  EVAL   Dummy
 26.001  HEAD         Internal A and B Triggering Test
 26.002  DISP         Move the Fluke 6061A RF OUTPUT via a 50ê feedthru
 26.002  DISP         termination to the UUT CH1 input connector.
 26.003  DISP         Set the UUT VERTICAL controls as follows:
 26.003  DISP
 26.003  DISP         ÿ   MODE ........................................... CH1
 26.004  DISP         Set the UUT HORIZONTAL controls as follows:
 26.004  DISP
 26.004  DISP         ÿ   MODE ............................................. A
 26.004  DISP         ÿ   A & B SEC/DIV ................ (A & B LOCKED) 0.05æs
 26.005  DISP         Set the UUT B TRIGGER controls as follows:
 26.005  DISP
 26.005  DISP         ÿ   SLOPE ............................... + (button out)
 26.006  6060         100MH                        100mVpp        -D    S
 26.007  MESS         Can a stable display be obtained by adjusting the
 26.008  EVAL   A TRIGGER LEVEL control?
 27.001  HEAD         {}
 27.002  HEAD         {CH1, A trigger mode P-P AUTO, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 27.003  JMP          28.001
 27.004  EVAL   Dummy
 28.001  HEAD         Internal A and B Triggering Test
 28.002  6060         100MH                        100mVpp        -D    S
 28.003  DISP         Set the UUT A TRIGGER controls as follows:
 28.003  DISP
 28.003  DISP         ÿ   SLOPE ................................ - (button in)
 28.004  EVAL   A TRIGGER LEVEL control?
 29.001  HEAD         {}
 29.002  HEAD         {CH1, A trigger mode NORM, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 29.003  JMP          30.001
 29.004  EVAL   Dummy
 30.001  HEAD         Internal A and B Triggering Test
 30.002  6060         100MH                        100mVpp        -D    S
 30.003  DISP         Set the UUT A TRIGGER controls as follows:
 30.003  DISP
 30.003  DISP         ÿ   A TRIGGER MODE ................................ NORM
 30.004  EVAL   A TRIGGER LEVEL control?
 31.001  HEAD         {}
 31.002  HEAD         {CH1, A trigger mode NORM, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 31.003  JMP          32.001
 31.004  EVAL   Dummy
 32.001  HEAD         Internal A and B Triggering Test
 32.002  6060         100MH                        100mVpp        -D    S
 32.003  DISP         Set the UUT A TRIGGER controls as follows:
 32.003  DISP
 32.003  DISP         ÿ   SLOPE ............................... + (button out)
 32.004  EVAL   A TRIGGER LEVEL control?
 33.001  HEAD         {}
 33.002  HEAD         {CH1, B trigger mode NORM, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 33.003  JMP          34.001
 33.004  EVAL   Dummy
 34.001  HEAD         Internal A and B Triggering Test
 34.002  6060         100MH                        100mVpp        -D    S
 34.003  DISP         Set the UUT HORIZONTAL controls as follows:
 34.003  DISP
 34.003  DISP         ÿ   MODE ............................................. B
 34.004  DISP         Set the UUT A TRIGGER controls as follows:
 34.004  DISP
 34.004  DISP         ÿ   A TRIGGER MODE ............................ P-P AUTO
 34.005  DISP         Set the UUT B TRIGGER controls as follows:
 34.005  DISP
 34.005  DISP         ÿ   LEVEL ..................................... Midrange
 34.006  EVAL   B TRIGGER LEVEL control?
 35.001  HEAD         {}
 35.002  HEAD         {CH1, B trigger mode NORM, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 35.003  JMP          36.001
 35.004  EVAL   Dummy
 36.001  HEAD         Internal A and B Triggering Test
 36.002  6060         100MH                        100mVpp        -D    S
 36.003  DISP         Set the UUT B TRIGGER controls as follows:
 36.003  DISP
 36.003  DISP         ÿ   SLOPE ................................ - (button in)
 36.004  EVAL   B TRIGGER LEVEL control?
 37.001  HEAD         {}
 37.002  HEAD         {CH2, A trigger mode P-P AUTO, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 37.003  JMP          38.001
 37.004  EVAL   Dummy
 38.001  HEAD         Internal A and B Triggering Test
 38.002  DISP         Move the Fluke 6061A RF OUTPUT via a 50ê feedthru
 38.002  DISP         termination to the UUT CH2 input connector.
 38.003  DISP         Set the UUT VERTICAL controls as follows:
 38.003  DISP
 38.003  DISP         ÿ   MODE ........................................... CH2
 38.004  DISP         Set the UUT HORIZONTAL controls as follows:
 38.004  DISP
 38.004  DISP         ÿ   MODE ............................................. A
 38.005  DISP         Set the UUT B TRIGGER controls as follows:
 38.005  DISP
 38.005  DISP         ÿ   SLOPE ............................... + (button out)
 38.006  6060         100MH                        100mVpp        -D    S
 38.007  MESS         Can a stable display be obtained by adjusting the
 38.008  EVAL   A TRIGGER LEVEL control?
 39.001  HEAD         {}
 39.002  HEAD         {CH2, A trigger mode P-P AUTO, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 39.003  JMP          40.001
 39.004  EVAL   Dummy
 40.001  HEAD         Internal A and B Triggering Test
 40.002  6060         100MH                        100mVpp        -D    S
 40.003  DISP         Set the UUT A TRIGGER controls as follows:
 40.003  DISP
 40.003  DISP         ÿ   SLOPE ................................ - (button in)
 40.004  EVAL   A TRIGGER LEVEL control?
 41.001  HEAD         {}
 41.002  HEAD         {CH2, A trigger mode NORM, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 41.003  JMP          42.001
 41.004  EVAL   Dummy
 42.001  HEAD         Internal A and B Triggering Test
 42.002  6060         100MH                        100mVpp        -D    S
 42.003  DISP         Set the UUT A TRIGGER controls as follows:
 42.003  DISP
 42.003  DISP         ÿ   A TRIGGER MODE ................................ NORM
 42.004  EVAL   A TRIGGER LEVEL control?
 43.001  HEAD         {}
 43.002  HEAD         {CH2, A trigger mode NORM, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 43.003  JMP          44.001
 43.004  EVAL   Dummy
 44.001  HEAD         Internal A and B Triggering Test
 44.002  6060         100MH                        100mVpp        -D    S
 44.003  DISP         Set the UUT A TRIGGER controls as follows:
 44.003  DISP
 44.003  DISP         ÿ   SLOPE ............................... + (button out)
 44.004  EVAL   A TRIGGER LEVEL control?
 45.001  HEAD         {}
 45.002  HEAD         {CH2, B trigger mode NORM, slope positive}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 45.003  JMP          46.001
 45.004  EVAL   Dummy
 46.001  HEAD         Internal A and B Triggering Test
 46.002  6060         100MH                        100mVpp        -D    S
 46.003  DISP         Set the UUT HORIZONTAL controls as follows:
 46.003  DISP
 46.003  DISP         ÿ   MODE ............................................. B
 46.004  DISP         Set the UUT A TRIGGER controls as follows:
 46.004  DISP
 46.004  DISP         ÿ   A TRIGGER MODE ............................ P-P AUTO
 46.005  EVAL   B TRIGGER LEVEL control?
 47.001  HEAD         {}
 47.002  HEAD         {CH2, B trigger mode NORM, slope negative}
# This jmp FSC is needed for Cancel and Repeat options during test run.
 47.003  JMP          48.001
 47.004  EVAL   Dummy
 48.001  HEAD         Internal A and B Triggering Test
 48.002  6060         100MH                        100mVpp        -D    S
 48.003  DISP         Set the UUT B TRIGGER controls as follows:
 48.003  DISP
 48.003  DISP         ÿ   SLOPE ................................ - (button in)
 48.004  EVAL   B TRIGGER LEVEL control?
 49.001  MESS
 49.002  HEAD
 49.003  DISP         [27][91]1mDisconnect the test set-up.
 49.004  END